Allen-Bradley 1784-KT/B Instrukcja Obsługi

Technical Reference For Allen-Bradley PLCs Merrick Industries, Inc. 10 Arthur Drive Lyn

A-B SuperBridge Technical Reference 5• SIO-485 Mode. E4 = {Dip Shunt @ SIO-485}. This is not the default setting. • Line terminations on. SW-2

A-B SuperBridge Technical Reference 6CONFIG.SYS \CONFIG.SYS They can all be edited with the MS-DOS editor ‘EDIT’. The default CFG_KT.INI file is

A-B SuperBridge Technical Reference 7DEVICE=KTX Must be present if KTX Card is used to interface with DH+. MEMORY=D700 Must correspond to the

A-B SuperBridge Technical Reference 8; SuperBridge DF1 Configuration ; 11/30/95/BPM [DTL_DF1.3] DEVICE=DF1 BAUD=19200 IRQ=4 COM_PORT=1 NAME=SB_

A-B SuperBridge Technical Reference 9C:\ABIC\BIN\CFG_485 C:\ABIC\BIN\RNATSR C:\ABIC\BIN\RNA -a8 CD SUPERB ABDRV There is normally no reason to

A-B SuperBridge Technical Reference 10SETTING UP COMMUNICATIONS WITH THE MCS The MC network is a four wire RS-485 Master-Slave polled communicat

A-B SuperBridge Technical Reference 113. Parity. Must be set to “NO Par” in all MCs. 4. Data Bits. Must be set to 8 in all MCs. 5. Start char

A-B SuperBridge Technical Reference 122. Check all communication parameters in all MCs. All parameters must be equal except the “Controller Num

A-B SuperBridge Technical Reference 13Using SB default segment parameters is highly recommended. See [PLCDefault] Section (page 43). At least t

A-B SuperBridge Technical Reference 14PLC FILE SPECIFICATION MC Data in SB is available in PLC style files. They are: • N12, containing read-on

A-B SuperBridge Technical Reference Revision Notes 0.70 10/02/95;LTM First complete issue 0.70A 11/08/95;LTM Typos, 20.00.K, 30.00.D, 11.00.HP

A-B SuperBridge Technical Reference 15failed. Bit 5 (0020) (x_INMENU) In menu. The MC menu system is engaged. This means that the effect of any

A-B SuperBridge Technical Reference 16MC General Alarms or Warnings, N12:3,11,19..(x_ALARMS) Any current general alarms or warnings in the MC is

A-B SuperBridge Technical Reference 17Fast Tag Register Number, N13:0,7,14..(x_FTAG) This is a numerical value of a register number in the MC. T

A-B SuperBridge Technical Reference 18Bit MC² keyboard key Hex Code Binary Code 14 "X" 4000 0100 0000 0000 0000 15 "ENT&qu

A-B SuperBridge Technical Reference 19Fast tagged value, F14:0,8,16..(x_FTAGV) This float contains the value of the register tagged in Fast Tag

A-B SuperBridge Technical Reference 20UNSOLICITED MESSAGES SPECIFICATION SB will act as a PLC when receiving unsolicited messages that request r

A-B SuperBridge Technical Reference 21element requested is beyond the last element in the SB requested file, extended error code 0xF00A is retur

A-B SuperBridge Technical Reference 22PLC-2 Unprotected Read See [6], page 3.2-8. With A-B terminology, this is command 0x01. Data will be retur

A-B SuperBridge Technical Reference 23MODEL SPECIFIC INFORMATION SuperBridge was released years after the MC² weighing controller. For some olde

A-B SuperBridge Technical Reference 24Note 3: See Setpoint (page 24). Note 4: An error in the 20.00.HP.O, A and B applications makes it imposs

A-B SuperBridge Technical Reference INTRODUCTION...

A-B SuperBridge Technical Reference 25Controller Bit Meaning 7 HPAD Not Set-Up 8 Test OverFlow 11.00.HP 1 Scale Overload 2 Scale Underloa

A-B SuperBridge Technical Reference 26Controller I/O Bit Meaning O 2 Low Speed Cut off O 4 In Control O 6 General Alarm I 8 Soft Start

A-B SuperBridge Technical Reference 27Note that the status of unused digital inputs in MCs are reported to the MC Digital I/O, N12:2,10,18.. (pa

A-B SuperBridge Technical Reference 28State Meaning 2 Normal LIW feed 3 Filling 4 Stabilization time after filling 5 Run cleanout cycle to lo

A-B SuperBridge Technical Reference 29State Meaning 30 Clearing the current Batch USEFUL REGISTERS All MC² applications contains a numbered

A-B SuperBridge Technical Reference 30DIAGNOSTIC SCREENS If a VGA compatible monitor and a PC keyboard is connected to the SB host PC, several d

A-B SuperBridge Technical Reference 31 THE HOME SCREEN 1 SuperBridge Home Screen 2

A-B SuperBridge Technical Reference 32 MC DATA SCREEN 1 MC Data, Controller Index 2 2

A-B SuperBridge Technical Reference 33Line Keyword Explanation and version is unknown to SB (not supported) 7 MC Current Status Possible status

A-B SuperBridge Technical Reference 34MC Combined Diagnostic Screen 1 MC Combined Diagnostic Port 0 Controller Index 0

A-B SuperBridge Technical Reference PLC TYPED MESSAGES...

A-B SuperBridge Technical Reference 35Line Keyword Explanation even if the specific version is not supported by SB. 14 ModelIdx A 0 here indi

A-B SuperBridge Technical Reference 36F1 Switch to The Home Screen (page 31) F2 Switch to A-B File Copy Diagnostic Screen (page 37) F3 Switch

A-B SuperBridge Technical Reference 37 A-B FILE COPY DIAGNOSTIC SCREEN 1 A-B File Copy Diagnostics

A-B SuperBridge Technical Reference 38Parameter Explanation Rejects How many file transfer attempts that has been rejected since SB was started

A-B SuperBridge Technical Reference 39A-B UNSOLICITED MESSAGES DIAGNOSTIC SCREEN 1 A-B Unsolicited Messages Diagnostics

A-B SuperBridge Technical Reference 40Unsolicited Messages Specification (page 19), which A-B data file was requested and the number of elements

A-B SuperBridge Technical Reference 41CONFIGURATION SB is completely configurable via the configuration file, SUPERB.INI. The file can be edited

A-B SuperBridge Technical Reference 42UartBase Base address for the UART, port N, hexadecimal. Default is 2F8 for section [Port0], which is the

A-B SuperBridge Technical Reference 43Port The index of the serial port to which the controller in connected. If a single serial port is used, d

A-B SuperBridge Technical Reference 44 MCPerSegment = 3 MCPerSegment = 5 Segment First Element Elements Segment First Element Elements

A-B SuperBridge Technical Reference SourceAddress ...

A-B SuperBridge Technical Reference 45Elements Number of elements for segment N. Max 100 for N files, 50 for F files. DataTypes Valid entries ar

A-B SuperBridge Technical Reference 46PLC2Base This is the PLC-2 address, in octal format, where the first SB file element (N12:0) is located. D

A-B SuperBridge Technical Reference 47[MC3] Port = 1 ; MC4 and MC5 are connented to the third port. [MC4] Port = 2 [MC5] Port = 2 ;

A-B SuperBridge Technical Reference 48REFERENCES [1] 1771 Information Processor User Manual Allen-Bradley Publication 1771-6.5.100, December 19

A-B SuperBridge Technical Reference 1INTRODUCTION SuperBridge (SB) is a software application that provides two-way communications between Merric

A-B SuperBridge Technical Reference 2upgraded. See Model Specific Information (page 23). The system response time will improve with decreasing n

A-B SuperBridge Technical Reference 3SETTING UP A SYSTEM Setting up a SB system includes the following steps: 1. Verify that existing MCs are e

A-B SuperBridge Technical Reference 4INSTALLING SB SOFTWARE AND HARDWARE If SB hardware and software are purchased entirely from Merrick, it com