Allen-Bradley 1609-P10000E Dokumentacja Pobierz pdf

1609-PSB1

Service Bypass Switch

reserved. Reproduction in whole or in part without permission is prohibited.

A-B and Allen-Bradley are registered trademarks of Rockwell Automation Corporation.

All other trademarks are the property of their respective owners.

90-007 rev 1

Note: Read the safety information sheet before installation.

Illustrations in this document may differ slightly from the actual hardware.

Attention: This product is for use in a controlled environment. Refer to product

specifications for environmental limits.

RACK MOUNTING

o Set SBP in the rack. If hardwiring is required, see Connecting Power

section before screwing into the rack.

n WALL MOUNTING

41063-300-01(1)

o Whenever possible, attach one top screw and one bottom screw into a wall stud. If stud

mounting is not possible, use an expandable wall anchor. Screws are not included; .25” x

2” lag bolts are recommended.

TOWER OPTION

n Remove screw from the top and bottom rear of both the UPS and SBP. Install tie

brackets and reattach screws.

o Unscrew and remove top cover of the

UPS.

p Attach bracket to top of UPS and SBP.

q Reattach top cover of the UPS.

Note: The 1609-SBP1, when used in conjunction with an 1609-P3000A or 1609-P5000E UPS in a tower

configuration without an external battery pack 1609-PXBP, is suitable for mounting on concrete or other

non-combustible smooth surfaces only.

41063-300-01(1)

USER CONFIGURABLE

Attention: When using an online UPS, put the UPS in automatic bypass mode before

rotating the SBP switch.

1. Normal: Power is directed from the utility outlet, through the Bypass Panel and UPS,

and to connected equipment. For use during normal UPS operation.

2. Test: Power supplied to the UPS is not output. Use when tests are being conducted on

the UPS, and connected equipment is not yet desired.

3. Bypass: Power from the utility outlet is filtered through the Bypass Panel, and to the

connected equipment. Use to bypass the UPS, when functioning improperly.

Note: While operating in ‘Test’ or ‘Bypass’ mode, power to the connected equipment is

not conditioned by the UPS. At this time, the “Equipment Protection Policy” is not valid.

IDENTIFYING THE PANEL

Service Bypass Panels will differ. Refer to chart for unit specifications.

Note: HW= Hardwire

Service Bypass

Panel

Corresponding

UPS Systems

Bypass

Input

UPS

Input

UPS

Output

PDU

Panel

1609-PSB1

1609-P3000A

1609-P3000H

1609-P5000E

1609-P8000E

1609-P10000E

HW (1Ph) HW (1Ph) HW HW

*For loads exceeding 3kVA, hardwiring is necessary.

41063-300-01(1)

Rea

Front

1 2

Podsumowanie treści

Strona 1 - Service Bypass Switch

Strona 2 - ROUBLESHOOTING

CONNECTING POWER Warning: Do not modify inlets or outlets. The SBP and UPS plugs and receptacles should match. For more information, contact Rockwe

Więcej dokumentów dla Zasilacze bezprzerwowe (UPS) Allen-Bradley 1609-P10000E

Aby wyświetlić dokument Allen-Bradley 1609-P10000E Instrukcja Użytkownika

Allen-Bradley 1609-P10000E Instrukcja Użytkownika (340 strony)

Allen-Bradley 1609-P10000E Instrukcja Użytkownika (17 strony)

Allen-Bradley 1609-P10000E Instrukcja Użytkownika (48 strony)

Allen-Bradley 1609-P10000E Instrukcja Użytkownika (5 strony)

Komentarze do niniejszej Instrukcji

Brak uwag

Allen-Bradley 1609-P10000E Dokumentacja

Przeglądaj online lub pobierz Dokumentacja dla Zasilacze bezprzerwowe (UPS) Allen-Bradley 1609-P10000E. Allen-Bradley 1609-P10000E Product specifications Instrukcja obsługi

Podsumowanie treści

Więcej dokumentów dla Zasilacze bezprzerwowe (UPS) Allen-Bradley 1609-P10000E

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Zasilacze bezprzerwowe (UPS) Allen-Bradley 1609-P10000E